Welcome to your comprehensive guide to the MITSUBISHI Base, tailored for New Zealand owners. This wiki provides essential information on maintenance, common issues, and WOF watch points to help you keep your MITSUBISHI Base running smoothly on New Zealand roads.

Parts for the Mitsubishi 4G32 (?-2999) - Variant 2

• Wiper Blade Front (15)
• Ignition Coil (10)
• Oil Filter (8)
• Brake Pads Front (5)
• Engine Mount Front (5)
• Wiper Refill Set Front (5)
• Oil Cap (4)
• Oil Pressure Switch/Sender (4)
• Starter Motor (4)
• Radiator Cap (4)
• Fuel Filter (4)
• Oil Seal Transmission/Gearbox Output Rear Extension (3)
• Oil Seal Crank Shaft Front / Timing Front (3)
• Universal Joint / Coupling Rear (3)
• Oil Seal Camshaft (3)
• Universal Joint / Coupling Front (3)
• Air Conditioning Compressor (3)
• Oil Seal Axle / Drive Shaft - Rear Outer (2)
• Wheel Bearing Kit/Hub Rear (2)
• Wheel Cylinder Rear (2)
• Spark Plug (2)
• Drive Belt Alternator (2)
• Valve Cover Gasket (2)
• Oil Seal Crank Shaft Rear / Rear Main Bearing (2)
• Drive Belt Pulley Idler/Tensioner (2)
• Oil Seal Oil Pump (2)
• Oil Seal Balance Shaft (2)
• Bearing Clutch Spigot (2)
• Oil Seal Differential Pinion Rear (2)
• Wheel Nut & Stud Rear (2)
• Wheel Bearing Front (2)
• Thermostat (2)
• Radiator Fan (2)
• Alternator (2)
• Ignition Lead Set (2)
• Wiper Refill (2)
• Steering Bush Steering Idler Front (1)
• Oil Seal Transmission/Gearbox Front Input (1)
• Oil Seal Hub Front Inner (1)
• Engine Mount Rear (1)
• Wheel Nut & Stud Front (1)
• Engine Oil Pan Gasket (1)
• Suspension Bush Radius Arm Front (1)
• Distributor Rotor (1)
• Wiper Blade Front & Rear (1)
• Wheel Bearing Kit/Hub Front (1)
• Wiper Blade (1)
• Oil Seal Hub Rear Inner (1)
• Wheel Bearing Front Outer (1)
• Differential Bearing Assembly Rear (1)
• Wiper Blade Rear (1)
• Switch Stop Light (1)
• Temperature Sensor / Sender Coolant (1)
• Brake Fluid (1)
• Air Conditioning Receiver Drier (1)
• Water Pump Gasket (1)
• Windscreen Washer Pump (1)
• Brake Hose Front (1)
• Suspension Bush Front Sway Bar Mount (1)
• Brake Pads Rear (1)

Known issues

Owners of MITSUBISHI Base vehicles should be aware of a couple of potential issues that may arise with age and usage:
• CV Joint Failures: Keep an eye on your CV joints, especially around the 150,000 - 250,000 km mark. Listen for clicking noises when turning, which can indicate wear.
• Rust in Wheel Arches: Rust can be a problem, especially in the wheel arches. Regular inspections and rust prevention measures can help mitigate this.

WOF tips

When taking your MITSUBISHI Base for its WOF (Warrant of Fitness) inspection, be mindful of the following common watch points:
• Corrosion around rear suspension mounts: Ensure these areas are free from significant rust.
• Excessive play in steering components: Any looseness in the steering system will likely result in a WOF failure.

About the Mitsubishi 4G32 (?-2999) - Variant 2

The MITSUBISHI Base, often seen in models like the Lancer or Galant, became a prominent part of the New Zealand automotive landscape as a dependable and budget-friendly option for families. These vehicles built a reputation for practicality and value.

Maintenance & Reliability:
Proper maintenance is key to the longevity of your MITSUBISHI Base. Regular servicing can help prevent common issues and ensure reliable performance. Pay particular attention to the condition of the brakes, filters, and suspension components. Standard New Zealand fitment parts should suit these models well.

DIY Considerations:
Owners with some mechanical experience will find that many maintenance tasks on the MITSUBISHI Base are moderately DIY-friendly. However, always consult a qualified mechanic if you are unsure about any procedure.

Questions owners ask

What are the common issues I should look out for with my MITSUBISHI 4G32 (?-2999) - Variant 2 –2999?

Owners of the MITSUBISHI 4G32 (?-2999) - Variant 2 –2999 should be aware of potential CV joint failures, especially between 150,000 and 250,000 km. Listen for clicking noises when turning. Additionally, rust in the wheel arches is a common problem, so regular inspections and preventative measures are recommended.

What should I pay attention to for my MITSUBISHI 4G32 (?-2999) - Variant 2 –2999's WOF inspection in New Zealand?

For your MITSUBISHI 4G32 (?-2999) - Variant 2 –2999's WOF, pay close attention to corrosion around the rear suspension mounts, ensuring these areas are free from significant rust. Also, check for any excessive play in the steering components, as looseness in the steering system will likely result in a WOF failure.

Where can I get replacement parts for my MITSUBISHI 4G32 (?-2999) - Variant 2 –2999 in NZ?

CARFIX stocks 165 SKUs for the MITSUBISHI 4G32 (?-2999) - Variant 2 –2999. You'll find standard New Zealand fitment parts for components like brakes, filters, and suspension, which are crucial for maintaining your vehicle's reliability.

How often should I service my MITSUBISHI 4G32 (?-2999) - Variant 2 –2999?

The recommended service interval for your MITSUBISHI 4G32 (?-2999) - Variant 2 –2999 is every 10,000 km. Regular servicing is essential for preventing common issues and ensuring the longevity and reliable performance of your vehicle.

Are MITSUBISHI 4G32 (?-2999) - Variant 2 –2999 vehicles easy to maintain for a DIY mechanic?

Many maintenance tasks on the MITSUBISHI 4G32 (?-2999) - Variant 2 –2999 are moderately DIY-friendly for owners with some mechanical experience. However, for more complex procedures or if you're unsure, it's always best to consult a qualified mechanic.

What are the key components to check for wear on my MITSUBISHI 4G32 (?-2999) - Variant 2 –2999?

When maintaining your MITSUBISHI 4G32 (?-2999) - Variant 2 –2999, pay particular attention to the condition of the brakes, various filters (oil, air, fuel), and suspension components. These are critical for safe and reliable operation.