
RDA Brakes · Part number RDC1308 · NZ$115.00 incl. GST
Right then, whether you're wrangling a rugged Mitsubishi Triton, cruising in a Toyota Corolla, or carving corners in a Nissan Skyline, brake pads are your absolute best mate for stopping power, turning all that go-fast energy into good old heat to bring you to a halt.
NZ$115.00 including GST. Part number RDC1308.
Brake Pad Swap-Out Guide — With a Nod to RDA
> Brake pads are the unsung heroes of your stopping system, doing the hard yards by creating friction against your rotors to slow things down or bring you to a complete stop. When they wear thin, you'll feel it — especially if you're hauling a heavy load in a Triton or pushing a Skyline to its limits. Don't muck about when it comes to brakes!
How You Know It's Time to Get Stuck In
• Your brakes are squealing like a banshee or grinding like a coffee machine.
• You're pressing the pedal further than usual to stop.
• A judder or vibration through the brake pedal.
• The pedal feels a bit squishy, like a worn-out jandal.
• A quick peek shows your pads are looking thin — less than 3mm of friction material left.
Will these pass the WOF?
Nah, mate, if your brake pads are worn down, that's a big no-no for safety and a guaranteed fail on your Warrant of Fitness. In Aotearoa, the legal minimum is usually 1.5mm, but honestly, you should be swapping them out well before that for peace of mind and top-notch stopping power.
DIY or Workshop?
Difficulty: 6/10 (A bit of a mission, but doable)
Estimated Time: 1-2 hours per axle (grab a cuppa halfway through)
Tools Required: Jack, sturdy jack stands (safety first!), wheel nut wrench, C-clamp or a piston compressor, spanner set, torque wrench, brake cleaner, wire brush, and maybe some brake caliper guide pin grease.
🛠️ Bob's "Get It Done Right" Companion Checklist
Before you dive into that brake job, Bob's got a few essentials to make sure you're sorted:
• Stay Safe, Stay Clean: Pop on some Safety Glasses to protect your peepers from dust and grime, and grab some heavy-duty Nitrile Gloves to keep your hands clean and chemical-free.
• Blast That Brake Dust: A good can of Brake Cleaner is your best friend here. It'll get rid of all that nasty brake dust and ensure a clean surface for your new pads.
• Smooth Operator: Don't forget some quality Anti-Seize Caliper Grease for those caliper pins. It helps things move freely and prevents seizing up down the track.
Expert Recommendation
Bob here at CARFIX can't stress this enough: get those brake pads replaced the moment you spot wear. It's not just about keeping your stopping power tip-top, it's about keeping you safe on our Kiwi roads. Letting them go too long can chew up your brake rotors, turning a simple pad swap into a much bigger, pricier job. These RDA RDC1308 pads are a solid choice — reliable and durable enough for anything from a hardworking Mitsubishi Triton to a slick Nissan Maxima. If you're scratching your head trying to figure out the right fit for your Mitsubishi L200, Toyota Corolla, or Nissan Skyline, just swing by Bob's Shop for a yarn. I'll get you sorted!
Fitment Notes
These pads are a good match for specific models including the Mitsubishi L200, Strada, and Triton (1996-2006), Nissan Maxima and Maxima QX (1995-2003), and Nissan Skyline (1993-2000), plus the Toyota Corolla (1996-2000). Always, always, always double-check your exact year, model, and engine variant to make sure you've got the right fit — especially if your ride has any quirky brake system specs. Don't guess, measure twice, fit once!
---
🛠️ Bob's Pro Tip: Do the Job Right!
🧰 What Else You'll Need:
• Safety First: Never work under a vehicle supported only by a jack. Always secure it on heavy-duty safety jack stands.
• Brake Dust Protection: Brakes get incredibly dirty. Keep a pack of Nitrile Gloves handy to protect your hands from stubborn brake dust.
• Clean and Prep: Use a high-quality Brake Cleaner spray to blast away stubborn dust, oil, and road grime from the caliper assembly and new rotors before reassembly.
• Lubrication: Apply a thin smear of high-temperature caliper grease to the pad backing plates and slide pins (keep it off the pad friction material!) to prevent squeals and ensure smooth caliper operation.